The One Ring
http://wwww.one-ring.co.uk/

Custom cast Project
http://wwww.one-ring.co.uk/viewtopic.php?f=50&t=29452		 Page 1 of 2
Author:  Oldman Willow [ Sat Sep 20, 2014 6:00 pm ]
Post subject:  Custom cast Project
My old WIP was too long so I started a new.

I met several of my Web friends at Gen Con. We made some mold swaps. It was really fun to meet them in person. I have been casting like mad from a set of molds that I borrowed.

Image

I will have a lot of sanding and fitting to do but I have begun to lay out parts.

Image

I am going to use the OOP E Bob figure for the buttresses. The center floor section will need to be complete before I can assemble the outer ring floor parts.

Image

Idea for a throne room for the old 1980's figures.
Author:  paliouras [ Sat Sep 20, 2014 6:05 pm ]
Post subject:  Re: Custom cast Project
I'm SOOOO jealous...
Author:  Pindergorn [ Sat Sep 20, 2014 6:40 pm ]
Post subject:  Re: Custom cast Project
Where'd you get those statues? And did you cast copies of them or are they all original plastic?
Author:  Oldman Willow [ Sat Sep 20, 2014 7:16 pm ]
Post subject:  Re: Custom cast Project
Image

cast part here kb.php?a=20
The painted non plastic figure is from E Bob the other white figure is a different sculpt. I have a mold for it.
Author:  Mapper [ Sun Sep 21, 2014 1:05 am ]
Post subject:  Re: Custom cast Project
Hirst Arts molds - a great sinkhole for time and money! Every time I think I have all the molds I need, I think of another project that requires just one more mold.
Author:  Oldman Willow [ Sun Sep 21, 2014 1:27 am ]
Post subject:  Re: Custom cast Project
Time to start creating your own.
Author:  Mapper [ Sun Sep 21, 2014 5:37 pm ]
Post subject:  Re: Custom cast Project
Yep, do that too. HA molds are great for gifts though, easy to ask for.
Author:  Celevue [ Sun Sep 21, 2014 7:07 pm ]
Post subject:  Re: Custom cast Project
Looking great - looking forward to seeing the Amon Sûl with all the parts, and love the throne room concept, too!
Author:  Gandlaf the Grey [ Sun Sep 21, 2014 7:55 pm ]
Post subject:  Re: Custom cast Project
Great work Charlie, another one to watch.
Author:  Oldman Willow [ Mon Sep 22, 2014 3:42 am ]
Post subject:  Re: Custom cast Project
Celevue wrote:
Looking great - looking forward to seeing the Amon Sûl with all the parts, and love the throne room concept, too!


Thanks.
Having the new molds has given me some new ideas. Amon Sul will be a lot of work.I am looking forward to working on it.

Thanks everyone for the nice comments.
Author:  Oldman Willow [ Wed Sep 24, 2014 6:58 pm ]
Post subject:  Re: Custom cast Project
Image

Harfoot's Photos are proving very helpful. The Tomes of Wisdom articles are also proving very valuable. Dagorlad's artical kb.php?a=53 and Geboom's kb.php?a=20

Image

Dagorlad's article inspired me to add the subterranean cave entrance to both models. I am taking advantage of the nice weather to cast.
Author:  Gandlaf the Grey [ Wed Sep 24, 2014 7:04 pm ]
Post subject:  Re: Custom cast Project
Looking like proper brown up Lego, I've got yo get some of these moulds.
Author:  Oldman Willow [ Wed Oct 01, 2014 11:34 pm ]
Post subject:  Re: Custom cast Project
I have cut out the base and will begin fitting and sanding.

Image

The base is made from MDF. I cut it out with a jig saw and circle cutter. I need to trim a bit with a drum sander. It is better to cut a little large than too small.
The cutter wabbled in the nail hole. My fault I don't use it often. I will fix it tomorrow.
Author:  Gandlaf the Grey [ Thu Oct 02, 2014 1:26 pm ]
Post subject:  Re: Custom cast Project
Looking impressive mate.
Author:  Oldman Willow [ Thu Oct 02, 2014 6:08 pm ]
Post subject:  Re: Custom cast Project
I learn my lesson working on Balin's Stair. The base need to be ready first.

Image

The floor base is on a 1/2" MDF base so that the Drop in LED fire pit will fit. I will use it when the orcs occupy it is some scenarios.Otherwise the fire pit will be in the cave. The small MDF blocks are spacers for the stairs.

Image

I put the next components on two rings. The stairs down to the cave will be cut into the top ring. The two rings fit on rizers around the floor. I will be able to save bricks and cut down on fitting this way.

The circle cutter I have does not fit my new jig saw. The old one is hard to get blades for. I should have put a cutter in the router but I didn't think of it till I was done.
Author:  Oldman Willow [ Fri Oct 03, 2014 8:01 pm ]
Post subject:  Re: Custom cast Project
Image

I am not going to spend a lot of time with filler at this stage so much is going to be covered with structure and broken stone. I drilled the hole for the battery box all the way through. The battery box was metric so my bit was 10/100 to small. I trimmed it but decided to change batteries from the bottom.

Image

I am going to make a few more custom molds. I need 32 more of the columns. I am going to cast a few more and put 8 on the custom mold.

Image

outside detail

Image

outside detail of provided mold cast and my idea on the right

Image

inside detai

Image

inside detail of provided mold cast and my idea on the right.

I could also cast some of the columns from the gothic detail mold instead of the ruined tower mold. The other detail column is from the cavern detail floor mold. I am not sure what looks best. Ideas?
Author:  Oldman Willow [ Sat Oct 04, 2014 5:01 am ]
Post subject:  Re: Custom cast Project
Image

a detail of the three steps from the large floor mold

Image

Image
Author:  Isilduhrr [ Sat Oct 04, 2014 1:59 pm ]
Post subject:  Re: Custom cast Project
looks great
Author:  Gandlaf the Grey [ Sat Oct 04, 2014 7:06 pm ]
Post subject:  Re: Custom cast Project
Love the way you have done the rubble etc at the bottom of the column, so authentic and makes a huge difference to this diorama.
Author:  Oldman Willow [ Sat Oct 04, 2014 8:21 pm ]
Post subject:  Re: Custom cast Project
Gandlaf the Grey wrote:
Love the way you have done the rubble etc at the bottom of the column, so authentic and makes a huge difference to this diorama.


That is the official promotional set. I am using it as a guide. One of my casting friends has the mold now. I am posting WIP photos with the guide so he can build his at the same time.

Image

only 1/2 I was never able to get The fullsize version.
Page 1 of 2 All times are UTC
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/