| The One Ring http://wwww.one-ring.co.uk/ |
|
| Glueing swords back on http://wwww.one-ring.co.uk/viewtopic.php?f=30&t=23637 |
Page 1 of 1 |
| Author: | RyuAzai [ Thu Aug 16, 2012 11:24 pm ] |
| Post subject: | Glueing swords back on |
So I was able to land an armored glorfindel from ebay a while ago, and I was really excited. Unfortunately in the shipping (Despite being wrapped amazingly.) the sword was weaken and then eventually fell of. One of the things I hate the most is superglueing swords back on models. It drives me INSANE, and I can never do it right. So any advice? What are your best techniques to glue swords back on? Best glue to use? How long should you let it sit? So you try to hold it together while it dries, or try to set it up to naturally push together? So far I have had no success on gluing glorfindel's sword back on. |
|
| Author: | IsleStaggerholm [ Thu Aug 16, 2012 11:35 pm ] |
| Post subject: | Re: Glueing swords back on |
Use super glue. Take a small pin set and drill a hole in the place where the sword broke off. Be careful to make it just slightly larger than the sword. The small hole should give you a base to rest the sword in and lend some stability. I will warn, however, that the sword will always be weak and have to be paid special attention to as not to rebreak it. |
|
| Author: | RyuAzai [ Thu Aug 16, 2012 11:56 pm ] |
| Post subject: | Re: Glueing swords back on |
Wow, I would have never thought of that thank you. For a pin set, are you taking of just some needles? Or is this something that comes with a sowing kit? |
|
| Author: | IsleStaggerholm [ Fri Aug 17, 2012 12:03 am ] |
| Post subject: | Re: Glueing swords back on |
Pin vice . . . hand drill. |
|
| Author: | Karak Norn Clansman [ Fri Aug 17, 2012 5:00 am ] |
| Post subject: | Re: Glueing swords back on |
Just use a pin vice to drill holes in the sword and its shaft (but not deep enough to damage the blade), then superglue the sword with a little piece of paper clip in the drilled holes to keep the miniature strong. This is called pinning. Pinning tutorial: http://www.warseer.com/forums/showthrea ... g-Tutorial For an advanced tutorial, click here: http://5-th-dimension.blogspot.se/2011/ ... tures.html |
|
| Author: | Oldman Willow [ Fri Aug 17, 2012 8:30 am ] |
| Post subject: | Re: Glueing swords back on |
You might want to try an accelerator http://www.amazon.com/Insta-set-acceler ... ccelerator A lot of people don't like Cyanoacrylate Accelerator. I use it but it is not a substitute for pining. Some people say it makes a weaker bond. I believe that is only if the object can be clamped in place instead. You can't clamp and glue something as small as a sword. So I don't think it will make any difference for replacing something like a weapon. One tip . Put the glue on the hand and the accelerator on the sword. It will bond instantly. Take care it is a good way to glue a model to your hand too. |
|
| Author: | Farthain [ Fri Aug 17, 2012 4:07 pm ] |
| Post subject: | Re: Glueing swords back on |
I got Mines of Moria about a month ago (plan on getting more if I can find an opponent over here!) When it got here, Legolas had a weakened bow. The top half fell of and I flipped, got freaking mad! After "work" that day (9 hours of babysitting) I was able to go out and get a small bottle of instant crazy glue. That stuff sticks! All you need is a little dab of it, and the bow was on. Now, Legolas is the only figure I wouldn't be worried about breaking! The main thing to remember is that the glue is very runny when it comes out. You need to hold the bow in place while it dries. It took me a few tries to get it right. After fixing Legolas, I accidentally cut off Sam's legs. I got mad at how brittle these were. Two dabs of glue and about five minutes later, her was back on! |
|
| Page 1 of 1 | All times are UTC |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|