title said; how do hou bend arms or weapons back in the wright position.
I heard mention of using hot water or something like that.
| The One Ring http://wwww.one-ring.co.uk/ |
|
| how to bend failca... I mean finecast minis http://wwww.one-ring.co.uk/viewtopic.php?f=30&t=23473 |
Page 1 of 1 |
| Author: | fritskuhntm [ Fri Jul 20, 2012 2:42 pm ] |
| Post subject: | how to bend failca... I mean finecast minis |
title said; how do hou bend arms or weapons back in the wright position. I heard mention of using hot water or something like that.
|
|
| Author: | John Wayne [ Fri Jul 20, 2012 3:14 pm ] |
| Post subject: | Re: how to bend failca... I mean finecast minis |
I used to use a hair dryer but i do not recommend it. Best way is a small bowl of kettle boiled water and submerge the model in for a minute and then take out and re-shape it, leave it to dry. |
|
| Author: | tlotrsbg [ Fri Jul 20, 2012 3:16 pm ] |
| Post subject: | Re: how to bend failca... I mean finecast minis |
ive found it works in seconds not a minute! .. id be concerned of bits falling off after a minute! perhaps im wrong |
|
| Author: | fritskuhntm [ Fri Jul 20, 2012 3:18 pm ] |
| Post subject: | Re: how to bend failca... I mean finecast minis |
alright, i'll try it. thanks for the quick reply! 
|
|
| Author: | Hashut's Blessing [ Fri Jul 20, 2012 5:40 pm ] |
| Post subject: | Re: how to bend failca... I mean finecast minis |
Hot, NOT boiling water. Boiling water for 2 seconds made the Beast of Gorgoroth's neck bendier than a bendy straw. |
|
| Author: | GothmogtheWerewolf [ Fri Jul 20, 2012 7:22 pm ] |
| Post subject: | Re: how to bend failca... I mean finecast minis |
Aye, hot tap water is sufficient. |
|
| Author: | Ring_of_Gyges [ Sat Jul 21, 2012 7:19 am ] |
| Post subject: | Re: how to bend failca... I mean finecast minis |
fritskuhntm wrote: title said; how do hou bend arms or weapons back in the wright position. I heard mention of using hot water or something like that. http://www.one-ring.co.uk/viewtopic.php?f=50&t=23357&start=40 I've had some luck with boiling water. |
|
| Author: | Sticky Fingersss [ Sun Jul 22, 2012 12:30 am ] |
| Post subject: | Re: how to bend failca... I mean finecast minis |
I used a REALLY hot lamp. It was extremely concentrated in where the heat was going (its like a superlamp) and it got it able to bend in 15-20 minutes for my great beast of gorgoroth. |
|
| Author: | Oldman Willow [ Sun Jul 22, 2012 2:05 am ] |
| Post subject: | Re: how to bend failca... I mean finecast minis |
Quote: Sticky Fingersss ยป Sat Jul 21, 2012 7:30 pm I used a REALLY hot lamp A hair dryer or heat gun will also work. One trick is to chill the warm plastic in cool water after you reform it. At least you don't have to hold it till it cools. Sadly  If it deformed once it will likely do it again. The larger models will most likely be ok for awhile.
|
|
| Author: | boromir_of_ithilien [ Mon Jul 30, 2012 6:46 pm ] |
| Post subject: | Re: how to bend failca... I mean finecast minis |
I left my Vault Warden spearman submerged in steaming water for three minutes before taking it out and bending it in place. I then put it in cold water for another three minutes after. I was able to straighten my spear to its proper angle. When I bought the model, its spear was at a 45 degree angle. However, it seems like the spear is starting to bend back down. I'm scared to straighten it up again because I already started painting it. 
|
|
| Page 1 of 1 | All times are UTC |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|