i freely take back all i have said about nuln oil. After a long (VERY long) time of shaking it turned out very well
thanks for the advice on this thread
| The One Ring http://wwww.one-ring.co.uk/ |
|
| Nuln oil not working? http://wwww.one-ring.co.uk/viewtopic.php?f=100&t=23902 |
Page 1 of 1 |
| Author: | Green_Dragon [ Fri Sep 28, 2012 5:56 am ] |
| Post subject: | Nuln oil not working? |
Hey guys, I purchased a pot of nuln oil when it first came out and used it to effect. I hadn't painted in a while and decided to have a little session and noticed a few of my newer washes were all whiteish/greyish at the top so I thought nothing of it and gave them a nice shake. However using my nuln oil now causes the paint to either dissappear or go that whitey grey colour in it's deepest recesses where it should be darkest. Wondering if anyone has had it happen and if they were able to fix it or best off buying a new pot? Thanks |
|
| Author: | SouthernDunedain [ Fri Sep 28, 2012 6:15 am ] |
| Post subject: | Re: Nuln oil not working? |
The only problem I had was that it went shiny because I didnt shake it enough. Was your brush clean? Also, give it a really good shake, like 30 seconds of solid shaking. |
|
| Author: | Dead Marsh Spectre [ Fri Sep 28, 2012 7:49 am ] |
| Post subject: | Re: Nuln oil not working? |
I have had this happen to with both nuln oil and badab black. I don't know why it happens but it is rather annoying. I have switched to vallejo inks now, much better. Out of interest how much nuln oil was left in the pot? |
|
| Author: | Green_Dragon [ Fri Sep 28, 2012 9:07 am ] |
| Post subject: | Re: Nuln oil not working? |
It's about 3 quarters full. I'll try giving it a longer shake but I'm not sure, it is annoying because I'm having to reapply it in the recesses making the figure darker than I wish. It only seems to 'fade' to the deepest recesses where it's at it's thickest. |
|
| Author: | Jobu [ Fri Sep 28, 2012 3:32 pm ] |
| Post subject: | Re: Nuln oil not working? |
Sounds to me like the medium/carrier they are using is separating from the color when water evaporates out of the pot. Try adding some water to it and then shake it very well. |
|
| Author: | Stormcrow [ Fri Sep 28, 2012 4:10 pm ] |
| Post subject: | Re: Nuln oil not working? |
I too have had this problem. The first couple of time i used it it dried a greyish white in the deeper parts of the models, which has been pointed out should be the darkest. I think it because the wash gathers too thick and dosnt seem to dry right. I just started doing lighter washes and then repeating with another wash once the first wash was dry until it looked the way I wanted it to. Never had a problem with badab black though and I did some really heavy washes with that. |
|
| Author: | Green_Dragon [ Tue Oct 02, 2012 12:17 pm ] |
| Post subject: | Re: Nuln oil not working? |
Thanks guys, yes thats exactly the problem I was having, I switched back to badab black for now but will try out adding more water to my pot of nuln oil. Will let you know how it goes! |
|
| Author: | SidTheSloth [ Thu Oct 04, 2012 7:45 pm ] |
| Post subject: | Re: Nuln oil not working? |
i freely take back all i have said about nuln oil. After a long (VERY long) time of shaking it turned out very well thanks for the advice on this thread
|
|
| Page 1 of 1 | All times are UTC |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|